Google Pixel 7 Pro Dump File Download & Dead Boot Repair Guide

Intro Why this guide matters

Pixel 7 Pro boards come with multiple UFS vendors and minor board revisions — which cause many “dead after flash” or bootloop issues. This guide gives you everything: the correctly matched dumps, the programmer files for common boxes, and step-by-step dead-boot / EDL flows that senior technicians use in the lab.

Device & Firmware Overview

Model: Google Pixel 7 Pro (Cheetah / Panther / G2 variations). Android Base: Android 13–15 depending on image. Storage/UFS: Samsung / SK Hynix / Micron variants — always check Vendor ID in device logs before writing.

What's included in the dump package

• Full UFS dump: raw partition images including userdata, system, vendor, vbmeta, fstab, and reserved partitions — for full restoration or cloning.
• Partial dump: GPT, boot, abl, vendor, modem, and radio partitions — used for dead-boot recovery while preserving user data where possible.
• Programmer files: rawprogram0.xml, patch0.xml, and specific payload installer files for boxes like EasyJTAG, UFI, Flash64.
• Firehose: authorized and tested firehose loaders (for EDL) — useful for Qualcomm provisioning flows on supported Pixel 7 Pro variants.
• Checksums & README: .sha256 files and a technician README with board mapping table.

Pre-flight checklist (must-do before flashing)

• Identify exact board and storage vendor: run fastboot getvar all or check EDL logs.
• Always backup UFS raw or at minimum /persist and /vendor partitions.
• Use a powered USB hub and quality USB-C cable — flaky connections cause half-write corruption.
• Charge device to >40% and ensure stable PC power.
• Download official factory images or the tested dump package from our download link and verify checksums.

Required Tools & Drivers

• Boxes: EasyJTAG Plus, UFI Box, Flash64, or ISP setup for UFS read/write.
• Software: Minimal ADB & Fastboot, QPST (if needed), QFIL (firehose), official OEM tools where applicable.
• Drivers: Google USB, Qualcomm QDLoader (EDL) drivers, and vendor-specific USB drivers.
• PC: Windows 10/11 recommended; administrator privileges.
• Optional: Heat gun for stubborn connectors during ISP, microscope for UFS pad work.

Step-by-step — Dead-Boot Repair (Multiple workflows)
Workflow A — EDL / Firehose (Qualcomm) — Best for dead-boot without bootloader

1. Confirm device in EDL: connect while holding required key combo or using test points — verify QDLoader in Device Manager.
2. Open QFIL (or your box firehose tool). Select patched/authorized firehose from the dump package.
3. Load programmer XML/rawprogram and patch files (supplied in package).
4. Select "Download" — monitor for "Finished" and verify all partitions written. Do NOT interrupt USB.
5. After finish, disconnect and boot to fastboot. If device enters fastboot, run fastboot reboot or reflash vbmeta/boot if required.

Workflow B — Fastboot / Factory Images (If fastboot accessible)

1. Boot device to fastboot (Volume Down + Power). Connect to PC and verify fastboot devices.
2. Unlock fastboot if permitted (technician/dev devices). Do not unlock if you must preserve user data.
3. Flash required images in order: fastboot flash abl abl.img, fastboot flash boot boot.img, fastboot flash vendor vendor.img, fastboot flash vbmeta vbmeta.img.
4. After flashing run fastboot -w if you want a clean system; skip it if preserving userdata with partial dump writes.
5. Reboot and verify system boots. If stuck, check logs with adb logcat (if booting) or serial logs via box.

Workflow C — ISP / JTAG / Direct UFS Programming (When neither EDL nor fastboot works)

1. Open the phone, connect to UFS pads using UFI/EasyJTAG ISP adapter or set up JTAG as required.
2. Perform a raw read of the UFS (if not previously done). Compare with provided full dump checksums.
3. Write the minimal partitions required for boot: GPT, ABL, boot, vendor, vbmeta.
4. Power cycle, reassemble, test boot. If boot succeeds, continue with modem and vendor patches.

Troubleshooting common errors

1. QFIL / EDL write fails mid-way

• Check QDLoader drivers and USB cable. Use different USB port or powered hub.
• Switch to alternative firehose or use vendor-specific authorized loader.
• If UFS is physically damaged, switch to ISP read/write and prepare for partial replacement or chip reballing.

2. Device stuck on Google logo (after flashing)

• Reflash vbmeta with correct AVB disable flags or sign images correctly.
• Verify fstab and vendor mismatch; some vendor images need matching boot and vendor.
• Try cold-boot: hold power for 15s then fastboot and reflash only the boot partition.

3. Baseband / Modem Unknown or No Network

• Flash appropriate modem and persist partitions from partial dump.
• Check /persist and /efs equivalents; restore backup from the dump.
• If IMEI missing, restore NVRAM backup — legal constraints apply in some jurisdictions, proceed only if owner-approved.

4. FRP / Account Lock after full restore

If FRP triggers, the device will require the original Google account. Use your lab's approved FRP bypass flows for devices you own or have authorization to service — see our FRP guide on the blog for methods and legal warnings: FRP Unlock Guide.

Expert tips & technician tricks

• Always verify vendor ID: Many Pixel 7 Pro images are identical except for UFS vendor blocks. Use logs to match (Samsung vs Hynix vs Micron).
• Partial writes first: Write just GPT+ABL+boot+vbmeta and test. If that boots, progressively write vendor and modem — reduces risk.
• Use checksums: Validate every image with .sha256 before writing.
• Keep a "clean bench image": Maintain one fully-working stock image per variant you service — reduces troubleshooting time.
• Document board IDs: Keep a mapping spreadsheet of serial numbers, board IDs, storage vendor, and which firehose works — saves hours.

Safety, legal, and backup best practices

• Obtain written consent from the device owner before altering FRP, IMEI, or user data.
• Never distribute copyrighted or OEM-authenticated firmware outside licensed agreements.
• Store backups securely; full UFS dumps contain sensitive personal data — treat them like PII.

Related resources

Further reading and tools on MobiFirms: Firmware index, Pixel dump & fixed files, How to unbrick Android (complete), Fastboot flashing guide, Best Android flash tools 2025, FRP unlock guide, Flashing Samsung guide (for comparative workflows).

You can find more Pixel-specific dumps and devinfo files in our Google Pixel section. :contentReference[oaicite:1]{index=1}

Conclusion & CTA

If you're a technician dealing with a dead Pixel 7 Pro, start with the partial dump approach and use EDL firehose programming if fastboot is unavailable. Download the fully-tested dump package and read the included README for specific board mappings.

Download Pixel 7 Pro Dumps & Recovery Package